用于BBB的4D系统Gen4 LCD触摸屏如何校准

@texasEE，这是我没有机会进行个人校准的屏幕之一。
我有机会测试4英寸和5英寸，所以那些已经实现了。
对于7英寸，这些值位于设备树覆盖中，从4英寸和5英寸显示器复制，仅禁用：  
github.com   
的BeagleBoard / bb.org的叠加/斑点/主/ SRC /臂/ BB-BONE-4D7R-01-00A1.dts＃L192-L193
//触摸屏偏移-X =;
//触摸屏偏移-Y =;      
在你的beagle运行：
debian @ test-bbb-2：〜$ cd /opt/source/bb.org-overlays/
debian @ test-bbb-2：/opt/source/bb.org-overlays$ git pull
已经是最新的。
debian @ test-bbb-2：/opt/source/bb.org-overlays$ nano src / arm / BB-BONE-4D7R-01-00A1.dts
取消注释： 
interrupt-parent =; 
中断=; 
//触摸屏偏移-X =; 
//触摸屏偏移-Y =; 
触摸屏的倒Y型; 
};
至： 
interrupt-parent =; 
中断=; 
触摸屏偏移-X =; 
触摸屏的偏移Y =; 
触摸屏的倒Y型; 
};
然后通过以下方式重建和安装：
debian @ test-bbb-2：/opt/source/bb.org-overlays$ make
debian @ test-bbb-2：/opt/source/bb.org-overlays$ sudo make install
然后重新启动测试。
问候，



以下为原文

        @texasEE, this is one of the screen’s i haven’t had a chance to personally calibrate yet. I had a chance to test the 4 and 5 inch, so those have it implemented.  For the 7-inch, the values are in the device tree overlay, copied from the 4 and 5 inch displays, just disabled:
        github.com        beagleboard/bb.org-overlays/blob/master/src/arm/BB-BONE-4D7R-01-00A1.dts#L192-L193

• //touchscreen-offset-x=<250>;
  
• //touchscreen-offset-y=<300>;
  

                On your beagle run:
debian@test-bbb-2:~$ cd /opt/source/bb.org-overlays/debian@test-bbb-2:/opt/source/bb.org-overlays$ git pullAlready up-to-date.debian@test-bbb-2:/opt/source/bb.org-overlays$ nano src/arm/BB-BONE-4D7R-01-00A1.dtsUn-Comment:
                                interrupt-parent = <&gpio0>;                                interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;                                //touchscreen-offset-x=<250>;                                //touchscreen-offset-y=<300>;                                touchscreen-inverted-y;                        };to:
                                interrupt-parent = <&gpio0>;                                interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;                                touchscreen-offset-x=<250>;                                touchscreen-offset-y=<300>;                                touchscreen-inverted-y;                        };Then rebuild and install via:
debian@test-bbb-2:/opt/source/bb.org-overlays$ makedebian@test-bbb-2:/opt/source/bb.org-overlays$ sudo make installand then restart to test.
Regards,

我已经尝试过编辑touchscreen-offset-x＆amp;
touchscreen-offset-y值从250到5000，结果非常少。
光标仍然从屏幕边缘附近的触摸位置偏离大约相同的量。
您能否提供预期数值的概念以及数字增加或减少时我应该期待什么？



以下为原文

        I’ve tried editing the touchscreen-offset-x & touchscreen-offset-y values from 250 to 5000 with very little results. Cursor is still off from touch position near the edges of the screen by about the same amount. Can you provide some idea of expected number values and what I should expect as number is increased or decreased?

@texasEE，我相信他们是微芯片触摸传感器的像素值......但是由于你没有得到任何好的反馈，请运行这个脚本并将它的输出分享给这个线程。
sudo /opt/scripts/tools/version.sh
问候，



以下为原文

        @texasEE, i belive they are pixel values in the microchip touch sensor… But since you aren’t getting any good feedback, please run this script and share it’s output to this thread.
sudo /opt/scripts/tools/version.shRegards,

/opt/scripts/tools/version.sh的输出
GIT中：/选择/脚本/：[73593ebe3b7d3cc381eeb502d45ccb33a6ec5e78]
EEPROM：[A335BNLT000C1826BBBG0816]
模型：[TI_AM335x_BeagleBone_Black]
dogtag：[BeagleBoard.org Debian Image 2018-01-28]
引导加载程序：[eMMC-（默认值）]：[的/ dev / mmcblk1]：[U-Boot的2018.01-00002-g9aa111a004]：[位置：DD MBR]
内核：[4.9.105-TI-R114]
的NodeJS：[v6.12.3]
uboot_overlay_options：[enable_uboot_overlays = 1]
uboot_overlay_options：[uboot_overlay_pru = / LIB /固件/ AM335X-PRU-RPROC-4-14-TI-00A0.dtbo]
uboot_overlay_options：[uboot_overlay_pru = / LIB /固件/ AM335X-PRU-UIO-00A0.dtbo]
uboot_overlay_options：[enable_uboot_cape_universal = 1]
uboot_overlay_options：[dtb_overlay = / LIB /固件/ BBB-VIPMOTOR-PRU-00A0.dtbo]
PKG检查：单独升级运行：[命令和apt安装--only升级＆安培; LT; PKG＆安培; GT;]
PKG：[BB-斗篷叠加]：[4.4.20180803.0-0rcnee0〜拉伸+ 20180804]
PKG：[BB-wl18xx固件]：[1.20170829-0rcnee2〜拉伸+ 20180104]
PKG：的kmod]：[23-2rcnee1〜拉伸+ 20171005]
PKG：[roboticscape]：[0.3.4-git20170602-0rcnee4〜拉伸+ 20171108]：[GOT_REPLACED_BY_NEXT]
警告：PKG：[librobotcontrol]：[NOT_INSTALLED]
PKG：[固件-TI-连通]：[20170823-1rcnee0〜拉伸+ 20170830]
组：[Debian的：Debian的ADM kmem的拨出光驱软驱音频视频畅游用户plugdev systemd期刊I2C蓝牙NETDEV cloud9ide GPIO PWM eqep管理SPI tisdk韦斯顿推出xenomai]
CMDLINE：[控制台= ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled = 1根=的/ dev / mmcblk1p1 RO rootfstype = EXT4 rootwait uboot_detected_capes = BB-骨LCD7-01，coherent_pool = 1M net.ifnames = 0安静]
dmesg |
grep pinctrl-single
[1.404269] pinctrl单44e10800.pinmux：142个管脚在PA f9e10800大小568
dmesg |
grep gpio-of-helper
[1.404883] GPIO-的辅助OCP：gpio_helper：准备
[1.405495] gpio-of-helper ocp：cape-universal：ready
结束



以下为原文

        Output from /opt/scripts/tools/version.sh
git:/opt/scripts/:[73593ebe3b7d3cc381eeb502d45ccb33a6ec5e78]eeprom:[A335BNLT000C1826BBBG0816]model:[TI_AM335x_BeagleBone_Black]dogtag:[BeagleBoard.org Debian Image 2018-01-28]bootloader:[eMMC-(default)]:[/dev/mmcblk1]:[U-Boot 2018.01-00002-g9aa111a004]:[location: dd MBR]kernel:[4.9.105-ti-r114]nodejs:[v6.12.3]uboot_overlay_options:[enable_uboot_overlays=1]uboot_overlay_options:[uboot_overlay_pru=/lib/firmware/AM335X-PRU-RPROC-4-14-TI-00A0.dtbo]uboot_overlay_options:[uboot_overlay_pru=/lib/firmware/AM335X-PRU-UIO-00A0.dtbo]uboot_overlay_options:[enable_uboot_cape_universal=1]uboot_overlay_options:[dtb_overlay=/lib/firmware/BBB-VIPMOTOR-PRU-00A0.dtbo]pkg check: to individually upgrade run: [sudo apt install --only-upgrade ]pkg:[bb-cape-overlays]:[4.4.20180803.0-0rcnee0~stretch+20180804]pkg:[bb-wl18xx-firmware]:[1.20170829-0rcnee2~stretch+20180104]pkg:[kmod]:[23-2rcnee1~stretch+20171005]pkg:[roboticscape]:[0.3.4-git20170602-0rcnee4~stretch+20171108]:[GOT_REPLACED_BY_NEXT]WARNING:pkg:[librobotcontrol]:[NOT_INSTALLED]pkg:[firmware-ti-connectivity]:[20170823-1rcnee0~stretch+20170830]groups:[debian : debian adm kmem dialout cdrom floppy audio dip video plugdev users systemd-journal i2c bluetooth netdev cloud9ide gpio pwm eqep admin spi tisdk weston-launch xenomai]cmdline:[console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk1p1 ro rootfstype=ext4 rootwait uboot_detected_capes=BB-BONE-LCD7-01, coherent_pool=1M net.ifnames=0 quiet]dmesg | grep pinctrl-single[    1.404269] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568dmesg | grep gpio-of-helper[    1.404883] gpio-of-helper ocp:gpio_helper: ready[    1.405495] gpio-of-helper ocp:cape-universal: readyEND

@texasEE，有点可疑，那不是GEN 4 LCD ......
U-Boot正在报道：
uboot_detected_capes = BB-骨LCD7-01，
哪个是旧款：https：//www.4dsystems.com.au/product/4DCAPE_70/
它使用am335'x adc输入作为电阻式触摸屏控制。
它的触摸事件不是很准确......
问候，



以下为原文

        @texasEE, something is fishy, that’s not a GEN 4 LCD…
U-Boot is reporting:
uboot_detected_capes=BB-BONE-LCD7-01,Which would be this older model: https://www.4dsystems.com.au/product/4DCAPE_70/
Which uses the am335’x adc input as a resistive touchscreen control. It’s touch events wasn’t very accurate…
Regards,

啊，那将是一个问题。
尝试调试此问题时切换显示。
一旦切换回4D Systems Gen4 7“显示器，值开始调整光标位置。在一些”播放“后发现x为100和y的275工作。
问题，似乎需要针对每个单元进行调整，或者除250和250之外还有一个好的默认值。
单位上出现的300个值可以过度补偿问题？
交互式开发每个单元的调整是一项繁琐的工作。



以下为原文

        Ah, that would be a problem. Switched displays while trying to debug this issue. Once switching back to the 4D Systems Gen4 7" display the values started to adjust the cursor position. After some “playing” found that x of 100 and y of 275 worked.
Question, it would appear that this needs to be adjusted for each unit, or is there a good default value other than the 250 & 300 values which appear on my unit to over compensate for the issue? It’s a cumbersome job to interactively develop the adjustment for each unit.

@texasEE完成了！  
github.com/beagleboard/bb.org-overlays      
BB-BONE-4D7R-01-00A1.dts：使用偏移用户@texasEE开始工作 
签约：Robert Nelson 
作者：RobertCNelson 
上午12:10  -  9月29日 
更改了1个文件 
有3个补充 
和2个删除。      
这将是未来的默认...并将很快通过apt update / upgrade安装......
问候，



以下为原文

        @texasEE done!
        github.com/beagleboard/bb.org-overlays                  BB-BONE-4D7R-01-00A1.dts: use offset user @texasEE got working

  Signed-off-by: Robert Nelson   by RobertCNelson  on 12:10AM - 29 Sep 18  changed 1 files  with 3 additions  and 2 deletions.                It’ll be the default going forward… and will be installed by apt update/upgrade shortly…
Regards,